Installation CD interface
CD interfaces are used for the manufacture of radio to communicate with an after-CD changer. Setting up your factory installed radio is defined as the interface connected to the back of your radio or pre-factory installed CD lead (where possible).
Not all pre-installed CD lead is compatible with the interfaces in such a case, you will simply ignore the pre-installed drivers and run the place as if there was. The descriptions in multipleonline stores will be accurate, or your car will have a pre-installed CD lead. If you do not have a pre-CD is not installed, the interface will lead to the back of CD Radio, which comes with the CD changer will be followed by the other side of the door and go to your location and installation CD.
Important: When you install the interfaces in order to ensure that the keys are completely removed from the ignition.
Interface – extra cable connections
A very small quantityinterface requires a few extra connection. But the producers are constantly interface redesign their interfaces to make all the connections so that the "Plug & Play" (push-points alone, without other connections). They realize that these components are still very popular with "DIY'ers" and then to make this change.
The maximum number of connections you can have two extra 12-volt cables to connect and a moat. 12 volt wires are switchedinflammation and permanent residence. It can on the back of the radio is connected.
Also included is a black thread of land into a nearby screw that comes in contact with the metal body of the vehicle or with a screw on your radio or mounting screw that mounts the CD changer will be protected.
Runs the command CD
* Turn off the CD out to radio and CD changer and check for proper operation and compatibility with CD before you can lead.
Many people think thatmore difficult than it really is. The best option is to run the CD leads off the passenger side of the car and pushed under the plastic liner that stretches from front to the rear of the car. With few cars that may need to remove trim to hide there, or under the carpet. Avoid turning points that the CD could pitch when screwing back and avoid tight areas that can trap the lead as the back seat when it is adapted. Insert the CD any excess cable in the distalchair or tie behind the glove compartment. When the head is extremely robust, it will not come under the rear seat is not damaged.
Mount the CD changer
* Check for correct operation and interoperability prior to installation of the Changer.
The most popular places to mount your CD changer in the trunk or under the front passenger seat. Many are also glove box big enough to accommodate a CD changer, especially the smaller models of 6 CD, MiniDisc or MP3 Changer. Compare CDMeasures to interchange with those available in the glove compartment.
CD changer at any angle of 90 degrees to be mounted (vertical) 180 degrees (horizontal), since there are no screws in the corner on both sides of the device with a screwdriver can be adjusted depending on the angle you need. Selecting the correct angle to prevent the plate from turning.
Suspension of the CD changer in the bottom of the rear tires (on saloon models) inside the shoe is a popular way to gobecause it keeps it hidden, and not taking any unused space. But, make sure that the magazine CD changer can be inserted and moved smoothly.
Easy installation with Velcro tape
We recommend that you just velcro the installation CD changer horizontal (flat) in a larger area that is used to connect the two mounting surfaces together to minimize any movement. Be aware that manufacturers do not really recommend a tear, but in our experienceWe found that this is a great way to mount the CD changer quickly and efficiently, especially the unpleasant places like glove boxes under the seats and flat surfaces, where the drill will be a difficult task. Audi A3 and BMW 3 Series is an excellent example (depending on boat design).
Strips of Velcro to keep the CD changer and then place the switch in the appropriate location of mounting. What you have to lose? As happened the slide to jump (be the first in our experience)only use brackets and screws provided as back-up plan.
Check before using screws
No matter how you mount the CD changer, so be sure not to drill and screw the bolts in the pan and the brake lines, etc. It can only be explored by drilling to avoid.
FM Modulator CD Changer
An FM modulator requires the installation of a permanent residence permit, direct ignition and an earth connection, a base /. The air from the existing radioFM modulator unit and air port device connected to the radio. You run the CD from the main unit is hidden behind the dashboard, glove box or kick panel and then mount the CD changer in your area.
Next mount the control display with Velcro adhesive to a surface, you see, select CD track, etc. If you want to use CD and then play a CD and put them in a specific radio frequency and saves this frequency / channel in a button your presetRadio band. CD Play in this shop is predetermined.
Related posts:
- CD Interface Installation
- Installation CD-ROM interface
- Upgrade Your Car Sound System – 7 Questions to help you decide what equipment you need!
- Improve Your Car Sound System – 7 Questions to determine what equipment you need!
- How MP3 Players Work? Digital Audio Technology Revolution music enjoyment
- How MP3 Players Work? Digital Audio Technology Revolution music service
- Shopping for a video MP3 player – look for higher quality
- Travel MP3 Player
- Sony LBT-GTZ4i 3-Disc CD Changer Mini Shelf System with Play Exchange
- Choosing a Car Audio System
Sorry, comments for this entry are closed at this time.